 |
 |
 |
(805) 481-9599 |
||
     |
||
ISOLATORS
DMXOPTO: Inline isolator
121: Isolation amplifiers
DINTAP / DININTR: DIN-rail isolator
ETHERNET PRODUCTS
E2E: Ethernet to Ethernet
E1REL20A: 1 Ch. Ethernet Relay
E8ANL-DIN: 8 Ch. Ethernet to Analog
NODE: Ethernet/DMX Interfaces
NODE DISCOVERY
PRE10ETHER-A: Ethernet Preset 10
ES2ETHER: Ethernet Entry Station Two
SPLITTERS
Splitter Selection Matrix
123/125/1211: 3, 5 or 11 output
124: 4 output DMX / RDM splitter
125EE: Enhanced five output
125EE-WALL: Enhanced wall mount
127: 7 output DMX / RDM splitter
1212: 12 output DMX / RDM splitter on DIN rail
SIGNAL ROUTERS
RR: Electronic patch bay
SW: Passive A/B switches
WIRELESS DMX512
Marconi TX: Transmitter
Marconi SP: 3 way splitter
Marconi LV: Low voltage receiver
MERGERS
221E: Enhanced 2,3,4,5 or 6 input
221E-WALL: Enhanced wall mount
POWER SUPPLIES
LED600: 24V 600W
LED400: 24V 400W
LED300: 24V 300W
LED100: Battery & Wireless
XFMR: Class 2 Transformer
WALL PLATES
WP-O/WP-I: Passive XLR plates
DFDNET: Buffered DMX512 plates
FIXTURES
EDISON: 25 lamp arrayable
DIMMERS
DMX8DIM: 8 Channel NEMA1
DMX12DIM-ELV: 12 Channel
DMX24DIM: 24 Channel
RELAYS
DMX1REL20A: 1 Ch. line voltage
DMX6REL15A/-30A: 6 Ch. line voltage
DMX2REL5A: 2 Ch. low voltage
DMX6REL1A: 6 Ch. low voltage
E1REL20A: Ethernet Relay
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMXDECELERATORII
DMX to DMX
DMX to AMX192 192 Ch.
DMX to Analog 12 channel
DMX to Analog 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
E8ANL-DIN: 8 Ch. Ethernet to Analog
Fire Alarm Interface
CONSOLES
APATHY: Single channel console
COLORWHEEL
PRESET 8 - DMX Snapshot Console
PRESET 10 - DMX Snapshot Console
PRESET 10 QUATTRO - 4 Universe
PRE10-A2: Preset 10 Architectural 2
PRESET 12 - DMX Snapshot Console
PRESET 18 - DMX Snapshot Console
PRE10ETHER-A: Ethernet Preset 10
RAD: RDM Address Device
RERUN - DMX Recorder
ES2: Entry Station Two
ES2ETHER: Ethernet Entry Station Two
DMX TESTERS
DMXdoohickey
DMXTSTR: DMX512 line tester
GIZMO: DMX512 test box
OTHER DMX STUFF
TERM: XLR Terminator w/ LED
T2: XLR Economy terminator
T-45: RJ45 Terminator
MOUNTING OPTIONS
RK: Rack Kits
JBOX: Product mounted in J-Box
CUSTOM & OEM
Click Here
Basic Specification
model: LED300
| Input power: | 115VAC, 50/60 Hz. 5.5A. Required UL statement: The LED300 must be located near the power outlet powering it and the outlet must be easily accessible. |
| Input signal: | DMX512, DMX512/1990, DMX512-A (250 Kb/s, 0.2 Volts min. 12 Volts max.) |
| Input circuit: | Transient protected EIA-485 transceiver (LT1785) |
| Input protection: | 15,000 Volt transient, ±60 Volt continuous |
| Input connector: | Gold plated 5 pin male XLR connector (Neutrik D-1 series) |
| Input pass through: | Gold plated 5 pin female XLR connector (Neutrik D-1 series) All five pins are passed through |
| Input isolation: | 600 Volts |
| Output signal: | DMX512-A when set for 5V differential data DMX512-A timings and protocol with 24V single ended levels when switched to 24V data |
| Output circuit (5V): | Transient protected EIA-485 transceiver (LT1785) yields an approximate 3V signal into 120 Ohms |
| Output circuit (24V): | MC34074 high speed op-amp tuned for 4uS bit period (250 Kb/s) yields approximately 22V at load |
| Output connector: | Gold plated 4 pin female XLR (Neutrik D-1 series) rated at 10 amps |
| Output current (power): | 12.5 amps (300 watts) continuous [limited to 5 amps (120 watts) maximum per output] |
| Indicators: | Red/green data type indicator, Red/green polarity indicator, Green signal indicator, Three digit DMX Start Address |
| User controls: | Three pushbuttons to increment DMX Start Address (hundreds, tens, and ones) |
| Operating modes: | Below is a list of start address and their corresponding outcome. 000 = Standard power supply operation. Connected devices must be addressed as needed. 1 - 512 = Enables DownShifter power supply operation. Connected devices are to be addressed to start address 1. |
| Standalone modes: | Below is a list of start address and their corresponding outcome. 6nn = Fixed colors where nn selects approximate Roscolux™ gel color. 7nn = Fading effects. The tens place selects an effect and the ones place adjusts the fade time. 8nn = Strobe effects. The tens place selects an effect and ones place adjusts flash rate. 900 = Random selection of fading and strobeing effects. |
| Color: | Black with white silkscreen nomenclature |
| Size and weight: | 9.25" h X 5.25" d X 9.75" w, 7.5 pounds |
| Mounting options: | Two 1/2" holes for half couplers or "C" Clamp and handle slot |
Doug Fleenor Design is a proud member of:
