ISOLATORS
  DMXOPTO: Inline isolator
  121: Isolation amplifiers
  DINTAP / DININTR: DIN-rail isolator

ETHERNET PRODUCTS
  E2E: Ethernet to Ethernet
  E1REL20A: 1 Ch. Ethernet Relay
  E8ANL-DIN: 8 Ch. Ethernet to Analog
  NODE: Ethernet/DMX Interfaces
  NODE DISCOVERY
  PRE10ETHER-A: Ethernet Preset 10
  ES2ETHER: Ethernet Entry Station Two

SPLITTERS
Splitter Selection Matrix
  123/125/1211: 3, 5 or 11 output
  124: 4 output DMX / RDM splitter
  125EE: Enhanced five output
  125EE-WALL: Enhanced wall mount
  127: 7 output DMX / RDM splitter
  1212: 12 output DMX / RDM splitter on DIN rail

SIGNAL ROUTERS
  RR: Electronic patch bay
  SW: Passive A/B switches

WIRELESS DMX512
  Marconi TX: Transmitter
  Marconi SP: 3 way splitter
  Marconi LV: Low voltage receiver

MERGERS
  221E: Enhanced 2,3,4,5 or 6 input
  221E-WALL: Enhanced wall mount

POWER SUPPLIES
  LED600: 24V 600W
  LED400: 24V 400W
  LED300: 24V 300W
  LED100: Battery & Wireless
  XFMR: Class 2 Transformer

WALL PLATES
  WP-O/WP-I: Passive XLR plates
  DFDNET: Buffered DMX512 plates

FIXTURES
  EDISON: 25 lamp arrayable

DIMMERS
  DMX8DIM: 8 Channel NEMA1
  DMX12DIM-ELV: 12 Channel
  DMX24DIM: 24 Channel

RELAYS
  DMX1REL20A: 1 Ch. line voltage
  DMX6REL15A/-30A: 6 Ch. line voltage
  DMX2REL5A: 2 Ch. low voltage
  DMX6REL1A: 6 Ch. low voltage
  E1REL20A: Ethernet Relay

INTERFACES
  Analog to DMX 48 channel
  RS-232 to DMX
  DMXDECELERATORII
  DMX to DMX
  DMX to AMX192 192 Ch.
  DMX to Analog 12 channel
  DMX to Analog 96 channel
  DMX to CMX / CMX to DMX
  DMX to Strand D54
  DMX to DALI
  DMX to Microplex/LMX/Ultraplex
  DMX to Solid State Relay 96 Ch.
  DMX iPlayer interface
  E8ANL-DIN: 8 Ch. Ethernet to Analog
  Fire Alarm Interface

CONSOLES
  APATHY: Single channel console
  COLORWHEEL
  PRESET 8 - DMX Snapshot Console
  PRESET 10 - DMX Snapshot Console
     PRESET 10 QUATTRO - 4 Universe
  PRE10-A2: Preset 10 Architectural 2
  PRESET 12 - DMX Snapshot Console
   PRESET 18 - DMX Snapshot Console
  PRE10ETHER-A: Ethernet Preset 10
  RAD: RDM Address Device
  RERUN - DMX Recorder
  ES2: Entry Station Two
  ES2ETHER: Ethernet Entry Station Two

DMX TESTERS
  DMXdoohickey
  DMXTSTR: DMX512 line tester
  GIZMO: DMX512 test box

OTHER DMX STUFF
  TERM: XLR Terminator w/ LED
  T2: XLR Economy terminator
  T-45: RJ45 Terminator

MOUNTING OPTIONS
  RK: Rack Kits
  JBOX: Product mounted in J-Box

CUSTOM & OEM
  Click Here

Discontinued
Replaced with the DMXDECELERATORII.

The DMX512 Inline Optical Isolator was designed to plug directly into the back of most DMX lighting consoles. Its primary purpose was to protect the console from hazardous voltages which may travel on the control cable. Hazardous voltages may be caused by dimmer failures, electrical storms, and cross wiring non-DMX equipment (foggers, intercoms, arc welders) into lighting control outlets. The isolator also eliminates ground loops and provides high drive current for long control runs.

NOTE: The input circuit of this inline isolator is passive and will not work with some DMX512 output circuits, specifically "slew-rate limited" circuits. Slew-rate limited applications require the active input circuit of our DMX Isolation Amplifier

Available connector types: 5 pin XLR only

Doug Fleenor Design is a proud member of: